Back to the Hens

IMG_2853

I remember first seeing The Serenity Prayer on a trivet that hung on my grandmother’s kitchen wall:

God, grant me the serenity to accept the things I cannot change,
courage to change the things I can,
and wisdom to know the difference.

I remember, even as a boy, being struck by it — the wisdom, not the trivet — and I find that it returns to my mind from time to time and brings perspective and encouragement.

It has been inspiring to see how so many people have changed things to work within our new set of circumstances.  Among them are those teachers of craft that rely to a large extent on traveling and teaching.  Peter Follansbee, to name one, has begun to expand his video offerings, as he explained  in this post.  I mention it here, for your benefit.  Peter began sharing incredible amounts of information through his blog back in 2008, and has just kept on going, with well over a thousand posts.  I was learning from Peter years before I met him, and still am.

After spending some time with Peter, you can have a go at a hen bowl.  I was able to get back to my rooftop hens I had started in this post last month.  I’ll pick up where I left off for those of you interested in tons of photos of a chunk of walnut getting smaller:

IMG_2754

The adze can’t reach effectively into this tight undercut hollow, at least mine can’t.  So I continued to excavate and shape with a bent gouge.  I also cleaned up the surface of the inner rim and drew a line for the final edge of the hollow.

IMG_2761

The tool will tell you when it has reached its limits.  For the deepest third or so of the hollow, I switched to a spoon bent gouge.  Between both gouges, it’s lots and lots of shavings and assessing with fingertips and eyes until the form of the hollow is nice and full.

IMG_2782

Before I started swinging my axe at the exterior, I took some measures to reduce the chances of knocking off that tail.  I made a few crosscuts, then progressively split off chunks of wood down to them.

IMG_2783

Leaves something like a Lego look to the back end.

IMG_2791

On the front end, I just start in with the axe, knocking off the ridges in distinct planes, which creates new ridges…

IMG_2792

…that are taken down, and so on.

IMG_2795

Eventually, the planes become narrower, more numerous, and curved.

IMG_2810

The tail end is a little more complicated.  I use an adze to go across the grain between the body and the flared tail.  I did some more shaping with the axe after taking the photo above.

IMG_2824

Then I faired the axed surfaces with a spokeshave.

IMG_2845

Then it’s time for a gouge and mallet to create a large channel under the wings.

IMG_2846

Here it is from above.  You’ve got to work downhill with the grain.  I just flipped to the other side of the pegs for the opposite two corners.

IMG_2839

Now it was time to reshape that wide body.

IMG_2847

I marked a rough line on the lower side of the channel.

IMG_2853

Then removed much of the material with the axe…

IMG_2858

…and cleaned up with the spokeshave.

 

IMG_2868

Pegs and holdfasts, you can do just about anything with them.  Here I was shaping the tail a bit more and scooping beneath it.

IMG_2881

There’s two of these going now, with slightly different proportions.  They’ve been drying for a few days.  I’ll get back to them for some flute carving and lots more fun,  heading toward something like this:

IMG_9874

A good way to start is with a smaller version in a softer wood.  The one below is only about eight or nine inches long and can be carved mainly with the same kit you’d use for spoon carving.

It might give your mind a break from those things you can’t change.

This entry was posted in bird bowls, bowls, holding, layout, Uncategorized, walnut and tagged , , . Bookmark the permalink.

12 Responses to Back to the Hens

  1. Eric Goodson says:

    Thank you for this post Dave. Encouraging in more ways than one. Hope all is well

    Liked by 1 person

  2. forwoodnesssake says:

    I was begining to think I was the only one to use a spoke shave on the out side of bowls and such.

    Liked by 1 person

    • Dave Fisher says:

      Works great for fairing surfaces, and, set heavy, can remove green wood quickly. I rarely use it as the tool for the final cuts, though that certainly is an option.

      Like

      • forwoodnesssake says:

        As you say; not for final cuts. I get close. Then I scrape and burnish to get rid of the tool marks.

        Like

  3. Bob Easton says:

    … a smaller version in softer wood … for practice.
    Great suggestion Dave! Thanks. [I think I have a block of basswood that will do.]
    Wife suggests they be roosters, not hens.

    Liked by 1 person

  4. Dave Fisher says:

    Yeah, I wonder about that too. How about “chickens?”

    Like

  5. hiscarpentry says:

    Your posts are always a treat to the eyes and mind. Thanks Dave. Can’t wait til this thing is over and we can all get together again!

    Liked by 1 person

  6. Dave Fisher says:

    I’ll be looking forward to that Nathan! Thanks.

    Like

  7. Thank you for the posts. I always enjoy reading them. You do beautiful work and your thoughtful approach to work and life is both calming and enlightening. Thank you for sharing. Hope you and your family remain both physically and mentally healthy in these times. Serenity Prayer is PERFECTO! michelle marguerite

    Like

  8. graemeu says:

    Love those breast feathers

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s