More Fun with Shrink Tubes

IMG_3169

Sometimes you just have to get an odd idea out of your system.  This one involved shrink pots, or more specifically, shrink tube bottoms.  I’ve written several posts about shrink pots/boxes/tubes with procedures and all that.  Here is a link to a list of those posts.

The whole idea of a shrink pot relies on the concept of a green dynamic ring of wood shrinking around a dry stable bottom.   And shrink tube interiors are perfectly round, straight from the auger.  The wheels started turning and I started measuring coins.  Turns out, a U.S. dollar coin is 1.043 inches in diameter, perfect for popping into the bottom of a shrink tube drilled with a 1 inch auger.  That exact measurement came from the U.S. Mint, here’s a link to their chart with all of the coin measurements.

IMG_3180

I noticed that a half-dollar coin is 1.205 inches and I have a 1 3/16 auger (1.19 inches)… so, now inspired by President Kennedy, I needed to figure out how to make the perfect groove to fit the coins.  Both coins are very close to 2mm thick, so that was at least consistent.

IMG_3211

I cut off the end of an old broomstick which was about 7/8″ in diameter and took a gouge to the inside of an old yard sale marking gauge to go around it as a fence.  There would be lots of ways to achieve the same idea.

IMG_3206

I simply drilled two holes in line with each other across the width of the broomstick and inserted two wood screws until the threads were below the surface.  Then I hacksawed the heads off, leaving just over 1/16″ rising above the surface of the wood.  I filed them to the width of the coins (2mm), then made a groove in one with a triangular file.  I refined the upper edges with a slipstone without reducing the width.  The other nub was simply filed flat at the front and an angle on top to form a bit of a chisel.

IMG_3214

I put the back end of the broomstick in a vice, slipped the tube over the front end until it was up against the fence and rotated the tube to the right while pressing down on the cutters.  The first cutter scores both sides of the groove and the second cutter clears the wood between.  I used light cuts going around several times, clearing the wet wood bits from the cutters often.  The result was a square groove that would fit over the edges of the coin.  The screws aren’t heat treated tool steel or anything, but they’re still steel cutting green wood; worked fine for this light duty.

Anyway, Noah and I had fun working out the procedures that worked best together.  We found that cutting a bit of a relief angle on the inner edge of the tube between the groove and the bottom edge of the tube allowed the coin to be funneled right down into the groove with a little pressure, then “pop,” it was in there.  It could move side to side in the groove until a couple days later when all of the play was gone and the groove had squeezed over the edges of the coin permanently.

IMG_3167

Noah and I painted them, then cut through the paint with a simple pattern of gouge chips.  The wood beneath was light in color.  Birch, cherry sapwood, and one aspen I think.  We used thinned artist oil paint to create more of a glazed effect.  On the third and fifth ones from the left, another different color after the carving.  We tapered the interior of the top a bit with the tapered reamer and found some nice natural corks straight from the bark that seal the deal.

IMG_3194

I like to use these things for pencil holders; the small ones hold about seven.  The tubes are easy to pop into a pocket, a pack, or even a tool roll.   They could also be handy for all sorts of things I suppose: tools, snacks, cigars?  Regardless, they’re a blast to make and would be a fun project to do with kids as well.  The possibilities for wood species and decoration are endless, and it’s a good use for straight small diameter pieces.

IMG_3159

Above are three small ones in blue, red, and green.  These are about 9 inches long.

IMG_3161

The half-dollar size are about 10 1/2″ long.  Gold over blue, India ink, and white over blue.

IMG_3184

We also made a shrink tube with the 2″ T-handle auger, the one in the middle there.  It’s 8 1/2″ long and has a wood bottom.

I hope you try making some of your own.  Leave a question in the comments if I can help clarify the process for you.  I see on the chart that a penny is 3/4″ and I’ll throw out the dime challenge.   And how big is a two pence?

This entry was posted in green woodworking, paint, patterns, shrink box, Uncategorized and tagged , , , . Bookmark the permalink.

25 Responses to More Fun with Shrink Tubes

  1. maydanlex says:

    How on God’s green earth do you think of this stuff. Brilliant!

    Like

  2. Jed Dillard says:

    This helps with something I’ve been thinking about a long time.
    When I was a boy, Mr Will Henry Esco had a sweet gum walking stick with a natural crook handle.
    At the end he had a
    “Mercury ” dime in it. Freedom of thought rather than Mercury, but I digress. He told us all if we could get the dime out we could have it. We didn’t.
    At some point I realized it must have been put in while the wood was green.
    I’ve always thought of putting a coin in like Mr. Will Henry’s, but I usually wait until my sticks are dry to make them.
    Guess my options are steaming the handles or cyanoacrylic glue. Think the glue would seem like cheating.
    A tad off topic, but a connection with memories and goals for me.
    Thanks!

    Like

    • Dave Fisher says:

      Love that story, Jed. Looking forward to seeing a dime in one of your walking sticks sometime, however you decide to do it. It will be interesting to see if you can get some kids to work on getting that dime out the way Mr. Will Henry Esco did!

      Like

  3. William Auld says:

    Brilliant!

    Liked by 1 person

  4. Scott Thomas says:

    Your creativity never ceases to amaze. And time well spent with Noah I’m sure will always be cherished.

    Like

  5. restorersart says:

    Heh. You realize that using metric and imperial/customary measures simultaneously immediately confers honourary Canadian citizenship?

    Like

  6. That croze is inspired!

    Like

  7. Amy says:

    Ohmygoodness I love these so much. Gives a whole new meaning to pencil/pen case. I love that Noah was in on them too!

    Like

  8. Dave Fisher says:

    Thanks, Amy! Noah said he prefers painting those over painting houses.

    Like

  9. onerubbersoul says:

    You are truly a wonder, Dave. I have a Kennedy half-dollar that belonged to my Grandfather…and this idea just made the list of answers for, “What am I going to do with this coin?”

    Liked by 1 person

  10. Frederik says:

    Very beautiful and clever.

    I just need to ask, how do you keep the carving clean when painting on the second colour layer. Or if you fill in the carving stop the paint from spilling over the edge. Your edges always are so clean, I absolutely love it.

    Liked by 1 person

    • Dave Fisher says:

      When I do two layers, I paint the first layer, then carve, then paint the second layer right over the first layer of paint and the freshly carved wood altogether. I typically take a paper towel and rub the second layer of paint from the surface to some extent. The second layer of paint effects the color of the first layer, especially if the first layer was put on very thin like a stain. So, for example, if I start with a thin coat of yellow, then carve a pattern through it, then go over everything with a thin coat of blue and wipe it back from the surface, the result will be a greenish surface with the carved bits blue and distinct borders. You can keep going like that and carve the surface again…

      The carved sign on this post might be a good example. scroll down to the second photo:
      https://davidffisherblog.wordpress.com/2019/08/18/spoonfest-2019/
      I started by just painting the flat surface of the board a bright blue with thinned artist oil paint. Then once that was dry, I carved the tree trunk and branches. Then I went over everything, blue surface and tree, with white and rubbed the surface. The white softened the original bright blue to the color that you see but made the carved tree simply white. Once the white was dry, I carved the words and the leaves.

      Really good question. I hope my explanation was clear enough.

      Like

      • Frederik says:

        Thanks for the explanation Dave, I don’t know if I ever encountered an explanation of yours that was not clear 😉
        I will try to wipe off the second layer sometime.
        Cheers

        Like

      • JReed says:

        I had the same question and have had some success, though your work is more precise. Great question, great answer.

        Like

  11. Neil Gray says:

    Lovely idea Dave. The design is so slick and clean lined.
    I did a similar idea for a small set of picks I use at work. I rounded a split branch then bored down the center with a 3/4″ auger leaving the end intact. For a cap I used a short piece of the same branch and bored it out a little and cut the bored section with a knife to fit over the end the main piece.
    I painted it with acrylic artists paints and oiled it.
    It’s much better than the cracked old plastic case.
    Your cork idea is a much better solution and looks stunning.

    Liked by 1 person

    • Dave Fisher says:

      I like that idea, Neil. Working one side of the split branch allowed you to leave that end-grain bottom. Either way, like you said — better than plastic! I like that cap idea too. Thanks.

      Like

  12. Peter says:

    Hi Dave,
    I love this idea. To answer your question, a two pence piece is 25.91mm or 1.02 inches in diameter. I would suggest using a pre-decimal penny, they are 30.8mm or 1.2 inches in diameter, about the same as your half dollar.

    Like

  13. Dave Fisher says:

    Thanks, Peter! And the two pence would work perfectly for the 1″ internal diameter. Bitcoins don’t stand a chance to catch on now!

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s