Adaptable Shaving Horse

IMG_6836

I was rooting around in the basement last weekend, and came upon a blast from the past: an attachment for my English-style shaving horse.  It was the beginning of the idea that ultimately resulted in my bowl horse.  Since writing the article, I’ve enjoyed hearing from others that have built their own bowl horses, either directly from the plans or some modified version. I really like using the bowl horse, but it is only beneficial for some operations.  Some may not want to go to the trouble of building one, or may not have the room.

When I saw that old board, I thought it might be useful to share how I used it before building my more specialized bowl horse.  Granted, the real bowl horse works better, but I made quite a few bowls with the original adaptation, and it only takes a half hour to make and doesn’t take up much room. So, if you’ve already got a shaving horse, you may be able to adapt it along these lines.

IMG_6838

This is the shaving horse I built years ago based on plans from Jennie Alexander. It’s a very simple design, and still works well on the occasions I make a chair or something.

IMG_6841

A couple clamps and a board are all I used to convert it into a horse that could hold a bowl from end-to-end.  A thicker board, and/or a heavier horse, would improve solidity.

IMG_6843

I just shaped a block of wood and attached it with screws.  The block of wood could easily be replaced by a vertical upright supported by a brace behind it.

IMG_6832

The swing arm now forces the bowl against the end block, holding it place for work with the drawknife or spokeshave.

IMG_6836

Temporarily screwing a board onto the arm assembly is a simple option that increases the surface area of the far jaw.

IMG_6837

Adjust for any size bowl by loosening the clamps and sliding the board.

It is nice to have a variety of holding options in terms of benches and accessories in the workshop, especially if one is making many different bowl designs.  Still, while I had the shaving horse out, I thought about how I might be able to simply adapt the English shaving horse in additional ways for bowl work.

IMG_6844

Simply dropping the support table creates a stop.  Sitting astride the bowl like this could allow certain operations to be done.

IMG_6845

Boring a few 3/4″ holes along the length of the bench allows for the use of holdfasts.

IMG_6847

The holes can also be used for pegs and wedges.  Adze work could be done in this position, but would be more ideal if the bench were a little wider and beefier.

IMG_6855

While sitting at the back of the bench, work with the drawknife was reasonably comfortable.

IMG_6859

And it was such a nice winter weekend, I knocked together one of these.  I’ve seen different versions of this concept in photos, including Robin Wood’s BowlMate.  Should make it nice to do some roughing outside without lugging benches out of the shop.

 

Advertisements
This entry was posted in carving, holding, tools, Uncategorized and tagged , . Bookmark the permalink.

11 Responses to Adaptable Shaving Horse

  1. Rudy Everts says:

    Wow, great! You are so full of good ideas, and it is very nice that you share them! Your conversion from a shaving horse to a bowl horse is simply brilliant. I love ideas that are straightforward enough that you say ‘why didn’t I think of that?’ 🙂

    Is that a new bowl in the making? (walnut?).

    Like

  2. Dave Fisher says:

    I’ve heard from a reader that can’t see the photos on my last two posts. He’s using Safari browser. Anybody else experiencing this or have suggestions? That stuff is beyond me — I just look to see if the squirrel is still running inside the computer.

    Like

  3. Rudy Everts says:

    I’m using Safari (on an Ipad) and everything loads for me, just fyi. Perhaps they need to update their browser, or clear their cache (under settings).

    Like

  4. Jen Shrock says:

    I was just getting started on making a bowl horse when this popped up. My primary interest is with spoons, with possibly an occasional bowl attempt at some point in the future. Your shave horse adaptations make me wonder if I should rethink that direction. After using all versions, what would you say is most user friendly and multi-functional for spoons?

    Like

    • Dave Fisher says:

      Jen, I don’t really use any kind of a horse much for spoons — normally going from the axe to the sloyd knife. You can use the bowl horse (with a support under the spoon) and a drawknife, but you can also adapt a traditional shaving horse for use with spoons, probably something involving a narrower work support. In your situation, if you want a horse, I’d probably recommend a traditional horse. You could adapt it a little for spoons and possibly make the adaptation from the article for an occasional bowl.

      Liked by 1 person

  5. Peter Skrzypczak says:

    David,

    Just wanted to say how much I enjoy receiving and reading your blog. I have not done any bowl carving, but am very keen to have a go. So many thanks for your generous information and the great videos etc. Really good and much appreciated.

    Regards

    Peter Skrzypczak (Skripjack)

    Sent from Windows Mail

    Like

  6. hammerwolfe says:

    When and where is your next class???

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s